| Unit is field configurable as Duplicator 1 IN - 2 OUT |
| D5074S | 2/1 Ch; N° 2 TC-RTD-Tx Pot Inputs; N° 1 mA-V Output; Fully Programmable, SIL 3 (1 yr) |
| D1035S | 1 Ch; Contact-Prox-LL-Magnetic Pick-up Input; 0 -50 KHz Range; Pulse Output |
| D1060S | 1 Ch; Cont-Prox-LL-Magnetic Pick-up Input; 0 -50 KHz Range; Pulse + mA-V + Trip Ampl. Output; |
| Fully Software Programmable |
| D1060S-049 | 1 Ch; Cont-Prox-LL-Magnetic Pick-up Input; 0 -50 KHz Range; Pulse + mA-V + Trip Ampl. Output; |
| Special Version with Clamping Diode; Fully Software Programmable |
| D5060S | 1 Ch; 0 -50 KHz Frequency Input; Analog Output plus Pulse Repeat or Alarm Output |
| D5265S | 1 Ch, I.S. Encoder Input; A, B, Z Outputs |
| D1061S | FieldBus / ModBus Isolated Interface; Communication speed up to 1,5 M bit/sec; |
| D1062S | Vibration Monitor Sensors Isolated Interface; SIL 2 (1 yr); |
| D1063S | 1 to 4 parallel 350 Ohm Load Cell Input; 5V, 80 mA total capability; 6-Wire IN-OUT; |
| Fully Transparent; 30.000 Division Accuracy |
| D1064S | 1 to 4 parallel 350 Ohm Load Cell Input; 5V, 80 mA total capability; 6-Wire Input; |
| 4-20 mA & Modbus Output; 30.000 Division Accuracy; Automatic Bridge Calibration System |
| CABF012 | Load cells cable with N° 3 twisted & screened 1mm2 pairs + overall screen (price x meter) |
| D1010D-002 | 2 Ch; 0 - 5 Vdc Input; 4-20 mA Output; Fix Range |
| D1010S-010 | 1 Ch; -30 + 30 Vdc Input; 4-20 mA Output; Fix Range |
| D1010S-015 | 1 Ch; 0 - 50 Vdc Input; 4-20 mA Output; Fix Range |
| D1010S-016 | 1 Ch; 0 - 120 mVdc Input; 4-20 mA Output; Fix Range |
| D1010S-017 | 1 Ch; -10 + 10 Vdc Input; 4-20 mA Output; Fix Range |
| D1010S-023 | 1 Ch; -5 + 5 Vdc Input; 4-20 mA Output; Fix Range |
| D1010D-029 | 2 Ch; -20 + 20 mA Input; 0-20 mA Output; Fix Range |
| D1010D-030 | 2 Ch; 0 - 10 Vdc Input; 4-20 mA Output; Fix Range |
| D1010D-035 | 2 Ch; 0 - 15 Vdc Input; 4-20 mA Output; Fix Range |
| D1010D-036 | 2 Ch; 0 - 20 mA Input; 0-20 mA Output; Fix Range |
| D1010S-038 | 1 Ch; -50 + 50 Vdc Input; 4-20 mA Output; Fix Range |
| D1010S-055 | 1 Ch; 0 - 70 Vdc Input; 4-20 mA Output; Fix Range |
| D1010D-061 | 2 Ch; 0 - 40 Vdc Input; 4-20 mA Output; Fix Range |
| D1080D | 2 Ch; Relay Output SPDT; Suitable for 3 Wire probes |
| D1081D | 2 Ch; O.C. Transistor Outputs; Suitable for for 3 Wire probes |
| D1180D | 2 Ch; Relay Output SPDT; Suitable for for 3 Wire probes; AC Power Supply |
| PSD1000 | Zone 2 Power Supply; II 3 G EEx nA IIC T4; 24 V - 0,6 A Output; For AC power of D1000 Modules |
| PSD1000/F | Zone 2 PS; II 3 G EEx nA IIC T4; 24 V - 0,6 A Output; For AC power of D1000 Modules with Alarm |
| PSD1001 | I.S. Power Supply; [EEx ia] IIC; 4 Parallelable Outputs each with 15 V - 20 mA; SIL 3 (LP) |
| PSD1001C | I.S. Power Supply; [EEx ia] IIB; 10 V -150 mA Output ; SIL 3 (LP) |
| PSU1003 | I.S. Power Supply Component; EEx ia IIB T4; 5 V - 160 mA Output |
| PSD1004 | I.S. Power Supply; EEx ia IIB; 5 V -160 mA Output; |
| PSD1210 | Zone 2 Power Supply; II 3 G EEx nA IIC T4; 24 V - 10 A Output; SIL 3 (N+1/ 3 yr) / SIL 2 (10 yr) |
| T3010S | 4-20 mA Intrinsically Safe 4.5 digit Indicator; Loop Powered; IP 65; Size 144x144x50 mm; |
| 20 mm high Display; Suitable for Wall Mounting; Flush or Pipe mounting using OPT 3092-93 |
| OPT3092 | Stainless Steel Bracket set and Gasket for Flush-Panel Mounting |
| OPT3093 | Stainless Steel Bracket set for 50-70 mm Pipe Mounting & SS set for Flush-Panel Mounting |
| D1092S | 1 Ch; SIL3 Relay; Out: N° 2 SPST NO Relay (1 for NE Loads & 1 for ND Loads); SIL 3 (20Yr) |
| D1092S-069 | 1 Ch; SIL3 Relay; Out: N° 2 SPST NO/NC Relay (1 for NE Loads & 1 for ND Loads); SIL 3 (20Yr) |
| D1092D | 2 Ch; SIL 3 Relay; Out: N° 4 SPST NO Relay (2 for NE Loads & 2 for ND Loads); SIL 3 (20Yr) |
| D1092D-069 | 2 Ch; SIL 3 Relay; Out: N° 4 SPST NO/NC Relay (2 for NE Loads & 2 for ND Loads); SIL 3 (20Yr) |
| D1093S | 1 Ch; SIL3 Relay; Out: N° 2 SPST NO Relay (1 for NE Loads & 1 for ND Loads); SIL 3 (20Yr) |
| With Line and Load Breakage Detection |
| D5090S | 1 Ch; SIL3 Relay for NE Load; SPDT NC 4 Amps OUT plus Service OUT; SIL 3 (10Yr) / SIL 2 (20yr) |
| Safty Function is De-energized Relay / De-energized Load |
| D5290S | 1 Ch; SIL3 Relay for NE Load; SPDT NC 10 Amps OUT plus Service OUT; SIL 3 (10Yr) / SIL 2 (20yr) |
| Safety Function is De-energized Relay / De-energized Load |
| D5290S-078 | 1 Ch; SIL3 Relay for NE Load; 2 NC 3 Amps OUT plus Service OUT; SIL 3 (10Yr) / SIL 2 (20yr) |
| Safety Function is De-energized Relay / De-energized Load |
| D5290S-079 | 1 Ch; SIL3 Relay for NE Load; 2 NC 4 Amps OUT / 110Vac Coil ; SIL 3 (10Yr) / SIL 2 (20yr) |
| Safety Function is De-energized Relay / De-energized Load |
| D5091S | 1 Ch; SIL3 Relay for ND Load; SPDT NO 4 Amps OUT plus Service OUT; SIL 3 (6Yr) / SIL 2 (20yr) |
| Unit is also SIL 3 for ND Load; SPDT NC 4 Amps OUT plus Service OUT; SIL 3 (10Yr) / SIL 2 (20yr) |
| Safety Function is Energized Relay / Energized Load or De-energized Realy / Energized Load |
| D5291S | 1 Ch; SIL3 Relay for ND Load; SPDT NO 10 Amps OUT plus Service OUT; SIL 3 (6Yr) / SIL 2 (20yr) |
| Unit is also SIL 3 for ND Load; SPDT NC 10 Amps OUT plus Service OUT; SIL 3 (10Yr) / SIL 2 (20yr) |
| Safety Function is Energized Relay / Energized Load or De-energized Realy / Energized Load |
| D5293S | 1 Ch; SIL3 Relay for NE Load; SPST NC 10 Amps OUT plus Fault OUT; SIL 3 (10Yr) / SIL 2 (20yr) |
| With Line-Load Open and Short Circuit, Loss of Power, Hearth Leackage Detection; RS485 OUT |
| Safety Function is De-energized Relay / De-energized Load |
| D5294S | 1 Ch; SIL2 Relay for ND Load; 2 x SPST NO 10 Amps OUT plus Fault OUT; SIL 3 (7Yr) / SIL 2 (20yr) |
| With Line-Load Open and Short Circuit, Loss of Power, Hearth Leackage Detection; RS485 OUT |
| Safety Function is De-energized Relay / De-energized Load; 2+2 relay blocks for increased availability |
| BUS | Extra Price for Power Bus Housing; Add: " /B " to model number |
| OPT1096 | Kit For Bus Mounting Include: N° 2 MOR016, N° 1 MOR017, N° 1 MOR022, N° 2 MCHP065 |
| One needed for each group of modules. |
| MOR 010 | Grey Terminal Block Laser Engraved: 1-2-3-4 |
| MOR 016 | Din Rail Stopper |
| MOR 015 | Plug-in terminal block male, vertical out, for Power Bus |
| MOR 017 | Plug-in terminal block male, horizontal out, for Power Bus |
| MOR 022 | Plug-in terminal block female, horizontal out, for Power Bus |
| MOR 046/2 | Terminal Block for APN005: Passive output for D1052* / D1053* / D1072* (1 each channel) |
| MOR 058 | Terminal Block for PLC Pulse Damping of D109X relay |
| MCHP 065 | Din Rail Anchor for terminal block side of the Power Bus |
| PPC1090 | Pocket Portable Configurator required to configure programmable units |
| PPC1092 | PC Adapter required to configure via PC programmable units; Include CABF010 & USB Adapter |
| SWC1090 | Software for modules configuration via PPC1092; Available on our web site free of charge |
| CABF010 | Sub D 9 Poles Female-Female Nul-Modem; 1800 mm lenght |
| USB adapter | USB to serial line RS-232 Adapter; |
| OPT1091 | Cold Junction Compensator to be ordered for THCs Inputs; One required for each input |
| V | Extra Price for Channel configuration according to Customer Specs. |
| MCHP 064 | Tagplate in policarbonate material |
| MCHP 090 | 72 mylar white lables for tagging (A4); Software for compilation on our web site free of charge |
| MCHP 139 | 5 mm Spacer for spacing of modules on custom boards PBCO series. |
| MCHP 061/3 | Dummy Bus module with Bus connector removed |
| D1000D | Dummy module to be used with custom boards PBCO series |
| D1091S | Common Allarm Module for D1000 Series with Fault Output, 1 SPDT Relay Output |
| D1002S | Redundant Power Connection & Common Alarm Module (SPST) for D1000 Series; Max 4 Amp |
| CABF025 | 30 cm flat cable to interconnect two PBCO-16-037 Boards |
| D1000R | 19" Rack unit, 3 units High, suitable for 16 D1000 series modules |
| JDFT 049 | 12 mm Power Bus Connector for DIN Rail Mounting; One needed for each BUS Module |
| JDFT 050 | 22 mm Power Bus Connector for DIN Rail Mounting; One needed for each BUS Module |
| MCHP196 | Bus End Stopper; One for each end of Bus Required |
| OPT5097 | Kit For Bus Mounting Include: N° 1 MOR017, N° 1 MOR022, N° 2 MCHP196 |
| One needed for each group of modules |
| MOR 017 | Plug-in terminal block male, horizontal out, for Power Bus |
| MOR 022 | Plug-in terminal block female, horizontal out, for Power Bus |
| MCHP183 | Blue Terminal Block Plug 12 mm |
| MCHP184 | Grey Terminal Block Plug 12 mm |
| MCHP185 | Blue Terminal Block Plug 22 mm |
| MCHP186 | Grey Terminal Block Plug 22 mm |
| D5001S | Common Alarm Module (SPST) for D5000 Series |
| D5202S | Redundant Power Connection & Common Alarm Module (SPST) for D5000 Series; Max 4 Amps |
| SWC5090 | Software for configuration available on our web site free of charge |
| PPC 5092 | PC Adapter required to configure programmable units; Mini USB Male to USB Ports |
| OPT 5091 | Cold Junction Compensator for TC Inputs; One per channel required |
| V | Extra Price for Channel configuration according Customer Specs. |
| IS CERT | Copy of I.S. Complete Certificate; Specify certificate type (IEC-Ex; ATEX; FM, UL, GHOST; …..) |
| TEST CERT | Copy of Individual Test certificate; One per each ordered instrument |
| MANUAL | Copy of Instruction Manuals in English Language; One free copy included per each order |
| EC DECL | Copy of EC Declaration of Conformity; One free copy included per each order |
| COO | Certificate of Origin; Available only for export area outside of EC |
| Note | Certificates, Data Sheets, Instruction Manuals free from our web site: www.gmintsrl.com |
| PBCO-D8-009 | 16 Ch. Board: 16 AI or 8 DI + 8 DO or 16 DI or 16 DO suitable for FBM 211, 241, 242, 207 |
| PBCO-D8-010 | 8 Ch. Board: 8 AO or 8 AI or 4AO + 4AI suitable for FBM 237, 201, 204, 205 |
| single or redundant connector |
3007751905 
1179322382 
+86 133 5788 9265 
info@wheat-auto.com 
